Flame Energy XTD 1.5-I Flame Energy Wood Burning Insert - Discontinued — Manual
Flame Energy · Manual · PDF, 463 KB
About the XTD 1.5-I Flame Energy Wood Burning Insert - Discontinued
Built by SBI (Osburn), these continuously welded, uni-body steel wood inserts are manufactured in North America with North American steel by Flame Energy.
THIS PRODUCT HAS BEEN DISCONTINUED, THIS PAGE IS UP FOR INFORMATIONAL PURPOSES ONLY
The Flame Energy XTD 1.5-I wood burning insert is ideal for increasing the efficiency of a fireplace, allowing it to heat every room evenly. Designed to be installed into an existing wood-burning fireplace, you can keep the classic look of your fireplace and enhance heat efficiency. Open burning fireplaces are inefficient, burning rapidly, putting off little heat into your living area, and pulling large volumes of air out of the home and up the chimney with most of the heat from the fireplace. The Flame insert allows a long burn time using little wood while providing air-tight, efficient combustion. Holding logs up to 19 inches long, the firebox is 1.8 cubic feet and allows output up to 60,000 BTUs, effectively heating up to 1,600 square feet of space. The insert includes a heat-activated 130 Cfm fan kit, but a Faceplate and Faceplate Trim Kit are required to complete the appliance. In addition, a 6" stainless steel chimney liner kit is also recommended for the purposes of safety and optimum operational performance. If you wish to install the insert into a fireplace on an exterior wall with an exposed chimney you should also consider installing a Draw Collar to avoid draft problems.
Features
- Model Number: FL-060
- Maximum heat output of 60,000 BTU
- Includes a heat-activated, 130CFM blower
- 1.8 cubic foot firebox
- Maximum log length of 19 inches
- Air-wash system
- Optimum efficiency: 75%
- May qualify for some government incentives.
- Tested by Intertek as per applicable standards (CSA/UL/ULC and/or others)
Options
- Faceplate kit(29" X 44") (AC03400)
- Black (OA10122), brass (OA10121) or brushed nickel (OA10123) finish faceplate trim kit (29" x 44")
- Fresh air kit adapter (5" diameter) (AC01298)
- Liner fastening system (AC02006)
- Liner offset adaptor (AC01370)
Specifications
| Specifications | Flame Energy XTD 1.5-I |
| Type of fuel | Wood |
| Recommended surface | 850 to 1600 sq. ft. |
| Blower | 130 CFM |
| Maximum output - EPA test wood | 34000 BTU |
| Maximum output - seasoned cord wood | 60000 BTU |
| Color | Metallic black |
| Minimum fireplace opening | 28 7/8"W x 13 1/8"D x 21 1/4"H |
| Exterior dimensions | 27"W x 23 1/2"D x 20"H |
| Exhaust pipe diameter | 6" |
| Centre line of flue outlet to the back | 6 7/8" |
| Centre line of flue outlet to the side | 13 7/16" |
| Type of chimney | 2,100 deg. F (1150 deg. C) |
| Recommended chimney diameter | 6" |
| Minimum chimney height | 12' |
| Firebox dimensions | 21 1/4"W x 14"D |
| Log positioning | Width |
| Maximum log length | 19" |
| Door opening dimensions | 17 3/4"W x 8 1/4"H |
| Type of door | Glass with cast iron frame |
| Minimum clearances to combustibles * | (Data expressed in inches. 1 inch = 25.4 mm) |
| Combustible side wall to unit | 13" |
| Combustible side mantle to unit | 10" |
| Combustible top mantle to unit | 22" |
| Combustible top shelf to unit | 29" |
| Minimum floor protection in front of unit | 18" / 16" |
| Projection in the room minimum / maximum | 7.75" / 9.75" |
| Glass surface | 16"W x 7.75"H |
| Steel thickness | ¼" |
| Weight | 350 lbs |
| Warranty | Limited lifetime |
| Test standard - safety | ULC-628 , UL 1482 |
| Test standard - emissions | E.P.A. Method 28 |
Photos
Need help with this?
We have sold and serviced these appliances since 1999. If you need a part or advice, call us.
406-300-1776